Page History
...
When you start the installer you see the installer welcome screen.
License dialog
In this step you can select your license which is needed for using Blueriq. If you provide the license.aql in this step, the license will be installed for the Runtime and Studio, and will be ready to use after installation.
When you click Next you can choose the type of installation:
...
Typical installation
The steps described in this section apply to the typical installation.
In this screen you can choose the Blueriq features you wish to install: Studio, Runtime, Customerdata, DCM-lists, CaseEngine and Document Renderer. Note that the latter three are only available if you install the Runtime.
Here you can also configure the Blueriq installation directory.
After this you are ready to install.
During installation a progress bar is shown.
The following screen lists the path to the Studio repository for backup purposes. For more information see backup the repository.
If you added a license during the installer it will show the dialog on the left. Otherwise the dialog on the right.
By default Blueriq will be launched when you finish the installation.
Custom installation
The steps in this section apply to the custom installation.
In this screen you can choose the Blueriq features you wish to install: Studio, Runtime, Customerdata, DCM-lists, CaseEngine and Document Renderer. Note that the latter three are only available if you install the Runtime.
Here you can also configure the Blueriq installation directory.
When you click next you can configure the port IIS uses. Default is 140150.
| Note |
|---|
this Any port specified in the installer is not checked for availability. |
When you click next you can configure the port of the Studio Server service uses and the port for the studio Rest Service. Defaults are 14093 and 14096.
If the checkbox "Start studio on install" is checked the Studio will be started after the installation is finished.
| Note |
|---|
these ports is not checked for availability. |
When you click next you can configure the ports of the PostgreSQL Service and History Service. Defaults are 14094 and 14095.
These Services are use by the new version management system which was introduced at 12.9, See switching versioning system for more information.
| Note |
|---|
these ports is not checked for availability. |
The next screen allows you the choose the type of authentication that Studio will use. For more information and configuration after installation see security and user management.
Next is the user that is used to connect to Blueriq Studio by the administration page. The default is listed.
| Note |
|---|
if you choose NTLM or NTLM custom for security configuration, you need to provide an active directory user here. If you choose custom authentication, you best leave this untouched. If you need to change the user, the configuration for the administration page will be changed, but you still need to manually create the user in Studio after installation. Without this, the administration page will not function. |
When you click next the port that the Runtime uses is asked. The defaults are 1409115091.
If the checkbox "Start runtime on install" is checked the Runtime will be started after the installation is finished.this port is not checked for availability.
In the next screen you can specify the user that the Runtime uses to connect to Studio. The default is listed.
| Note |
|---|
if you choose NTLM or NTLM custom for security configuration, you need to provide an active directory user here. If you choose custom authentication, you best leave this untouched. If you need to change the user, the configuration for the runtime (Studio connection) will be changed, but you still need to manually create the user in Studio after installation. Without this, the runtime will not be able to connect to the Studio. |
When you click next the port that Customer Data Service uses is asked. The defaults are 1409715097.
If the checkbox "Start customerdata on install" is checked the Customerdata service will be started after the installation is finished.
this port is not checked for availability.
When you click next the port that DCM Lists Service uses is asked. The defaults are 14098.
If the checkbox "Start DCM Lists on install" is checked the DCM Lists service will be started after the installation is finished.| Note |
|---|
this port is not checked for availability. |
When you click next the port that Document Renderer Service uses is asked. The defaults are 1409915099.
If the checkbox "Start document renderer on install" is checked the Document Renderer service will be started after the installation is finished.
| Note |
|---|
this port is not checked for availability. |
After this you are ready to install.
During installation a progress bar is shown.
The following screen lists the path to the Studio repository for backup purposes. For more information see backup the repository.
If you added a license during the installer it will show the dialog on the left. Otherwise the dialog on the right.
By default Blueriq will be launched when you finish the installation.
Installation finished
...
Overview
Content Tools