Page History
...
When you start the installer you see the installer welcome screen.
...
In this step you can select your license which is needed for using Blueriq. If you provide the license.aql in this step, the license will be installed for the Runtime and Studio/Encore, and will be ready to use after installation.
When you click Next you can choose the type of installation:
Typical installation
The steps described in this section apply to the typical installation.
In this screen you can choose the Blueriq features you wish to install: Studio, Runtime, Customerdata, DCM-lists, CaseEngine and Document Renderer. Note that the latter three are only available if you install the Runtime.
Here you can also configure the Blueriq installation directory.
A Studio/Encore user named admin will be created during the installation. To do so, a valid password needs to be entered here.
An admin user for the user management in Keycloak of Studio/Encore will also be created during the installation. To do so, a valid password needs to be entered here.
After this you are ready to install.
During installation a progress bar is shown.
The following screen lists the path to the Studio Server repository for backup purposes. For more information see see backup the repository.
If you added a license during the installer it will show the dialog on the left. Otherwise the dialog on the right.
By default Blueriq will be launched when you finish the installation.
Custom installation
The steps in this section apply to the custom installation.
In this screen you can choose the Blueriq features you wish to install: Studio, Runtime, Customerdata, DCM-lists, CaseEngine and Document Renderer. Note that the latter three are only available if you install the Runtime.
Here you can also configure the Blueriq installation directory.
A Studio/Encore user named admin will be created during the installation. To do so, a valid password needs to be entered here.
An admin user for the user management in Keycloak of Studio/Encore will also be created during the installation. To do so, a valid password needs to be entered here.
When you click next you can configure the port IIS uses. Default is 150160.
| Note |
|---|
Any port specified in the installer is not checked for availability. |
When you click next you can configure the port of the Studio Server service uses and the port for the studio Rest Service. Defaults are 15093 16093 and 1509616096.
If the checkbox "Start studio on install" is checked the Studio will be started after the installation is finished.
When you click next you can configure the ports of the PostgreSQL Service and History Service. Defaults are 15094 16094 and 1509516095.
These Services are use by the version management system.
The next screen allows you the choose the type of authentication that Studio will use. For more information and configuration after installation see Studio Security Modes.
Next is the user that is used to connect to Blueriq Studio by the administration page. The default is listed.
When you click next the port that the Runtime uses is asked. The defaults are 1509116091.
If the checkbox "Start runtime on install" is checked the Runtime will be started after the installation is finished.
In the next screen you can specify the user that the Runtime uses to connect to Studio. The default is listed.
When you click next the port that Customer Data Service uses is asked. The defaults are 1509716097.
If the checkbox "Start customerdata on install" is checked the Customerdata service will be started after the installation is finished.
When you click next the port that Document Renderer Service uses is asked. The defaults are 1509916099.
If the checkbox "Start document renderer on install" is checked the Document Renderer service will be started after the installation is finished.
After this you are ready to install.
During installation a progress bar is shown.
If you added a license during the installer it will show the dialog on the left. Otherwise the dialog on the right.
By default Blueriq will be launched when you finish the installation.
Installation finished
When the installation is finished, the Blueriq start page is launched. Note that you first have to put the license file in the right location before you can start anything. For that and other configuration please take a look at Studioat Encore.
Configuration
After installation is finished, continue to configuration of Studio and/or of Encore and/or Runtime.
Logging
The installer will always save a log file during install on the location : %appdata%\Blueriq\
In case of an error during installation the log could give you more information about the cause of the error.
Common installation problems
| Content by Label | ||||||||
|---|---|---|---|---|---|---|---|---|
|
Overview
Content Tools